336MM3-T-WS and V92MM3-T-WS
336MM3-RC and V92MM3-RC (RoHS compliant) International DAA, Serial TTL Interface Modem Module
The MM3 families are based on Conexant’s newly developed SmartV(128) modem chipsets. New features include V.44 Data Compression and V.92, 48kbps upstream data speed for more efficient and faster data throughput. The modems also offer V.29 POST Fast-connect and reduction in power consumption. This feature-rich modem module family is fully self-contained including built-in data pump, modem controller and on-board International DAA. Standard features of the modem include data rates up to 56 kbps, 14.4 kbps fax, voice playback and recording. The modem also provides enhanced features such as Caller ID, Extension Pick-up detection, Remote Hang-up, DLG (Digital Line Guard) protection. Features:
-40oC TO +85oC extended operating temperature
Supports 3.3V to 5V operation
Serial TTL Interface
AT Command set
Up to 56 kbps data speeds downstream (V92MM3)
Up to 48 kbps data speeds upstream (V92MM3)
14.4 kbps Fax – Class 1
Voice playback and recording
Concurrent DTMF, distinctive ring and caller ID
V.44 data compression (V92MM3)
V.42bis and MNP-5 data compression
V.44 data compression
V.29 FastPOS support
Sleep mode
Line-in use detection
Call waiting detection
Extension pick-up detection
Digital Line Guard (DLG) Protection
2nd Ring Detect (optional)
Built-in phone jack (optional)
Transferable FCC68, Industrial Canada CS-03 registration, CTR21 certified
-
RoHS Compliant (models V92MM3-RC and 336MM3-RC)
-
cUL 60950 Recognized Component
Countries supported by existing firmware:
Australia, Austria, Belgium, Brazil, Canada, China, Denmark, Finland, France, Germany, Hong Kong, India, Ireland, Italy, Japan, Korea, Malaysia, Mexico, Netherlands, Norway, Poland, Portugal, Singapore, South Africa, Spain, Sweden, Switzerland, Taiwan, UK, US and TBR21 Generic.
Note:
More country codes are available, please contact Radicom for information.
More country Telecom Agencies such as Iceland, Luxembourg, Israel may adopt the TBR21 standards. The existing firmware could then be used to support those countries.
Ratings @ 25o C
Parameter |
Min |
Typ |
Max |
Units |
Tip / Ring Current Continuous |
10 |
20 |
120 |
mA |
Dielectric Withstanding Voltage |
|
|
1500 |
VRMS |
Operating Temperature |
-40 |
|
+85 |
°C |
Relative Humidity (non-condensing) |
10 |
|
95 |
% |
Voltage Requirement |
3.00 |
|
5.25 |
VDC |
- Power Consumption |
346 |
|
871 |
mW |
- Current Consumption
|
110 |
139 |
166 |
mA |
Transmit & Receive Level |
-10 |
-20 |
-43 |
dBm |
Mechanical Diagram & Pin Assignments - Serial Interface Note:
Header extends on non-component side. Can be reversed if necessary. (contact factory)
Header length is 0.236" on non-component side.
Pin spacing is 0.100" from center to center.
Tip and ring trace clearance must exceed 0.100" metal to metal.
0.350" H on component side (0.20" optional)
Single RJ -11 phone jack on component side (optional) - 0.60"H
Suggested mating female connectors: Through Hole: a. Samtec P/N. #SSW-110-01-G-D (RoHS) b. Molex P/N. #90147-1208 (non-RoHS) SMT: a. Samtec P/N. #SSW-110-22-G-D-VS (RoHS)
______________________________________________________________________________________________________ Information furnished by Radicom Research is believed to be accurate and reliable. However Radicom Research assumes no responsibility for its use, or any infringement of patents or other rights of third parties which may result from its use. Radicom Research reserves the right to change circuitry at any time without notice. This document is subject to change without notice. The information contained herein is subject to change without notice. Logos, trademarks and copyrights are property of their respective owners.
|