Ethernet to Serial/Modem Adapter Board
|
|
|
LSDB-8300 Series
|
|
|
Introduction:
The Radicom LSDB-8300 series offers an embedded solution for a Ethernet to Serial or Ethernet to Modem interface. The LSDB-8300M Module provides the reserved through hole (DIP) pin headers for the Serial Port TTL I/O and Ethernet pins that allow the Jacks to be placed in preferred locations. The TTL I/O can then be converted to RS232 signaling and connected to a DB9 connector to provide a fully compliant V24/V28, RS232 interface. Interface. The LSDB-8300NE is a standalone product embedded with a RJ45 Ethernet jack to provide the Ethernet interface and DB-9 for RS232 direct plug-in. The LSDB-8302T is a standalone product provides easy connection to any standard Ethernet port and Tiny Modem dial-up network. The LSDB-8303A is an All-in-one solution to provide POE, SIA alarm Modem, WiFi, RS232/485.
LSDB-8301HM is a small form factor of Ethernet to SIA alarm and LASDB-8301HC is not only provide analog SIA modem as well as emulate central office with line current provided.
This product allows serial data communication with any 10/100 Based-T Ethernet LAN. The LSDB-8300EVK along with LSDB-8300MB development board also provides RJ45 and DB9 connectors for LSDB-8300M module testing and developing purpose.
The onboard Ethernet functions are designed to meet the widely adopted IEEE Std. 802.3™ with automation and buffering. The integrated serial port includes standard serial terminal features such as flow control, character length and a DTE speed of 921.6Kbps. The LSDB-8300 series includes Flash memory allowing for updating firmware with the latest
enhancements and for custom applications. Users can make changes to web server applications such as configuration of local hardware using Telnet or FTP.
Ethernet Features:
- Designed to meet IEEE Std. 802.3™
- Supports IEEE 802.3az energy efficient Ethernet ability for 100Base-TX in full duplex operation and 10Base-T in full/half duplex mode
- Supports Green Ethernet
- Cable length power saving
- Link down Power saving
- Supports link down power saving in Ethernet PHYceivers.
- Ethernet port auto-crossover function.
- Complete Serial-to-Ethernet solution with network processor, MAC (media access controller) and PHY interface.
- Multiple IP Address Configuration Modes: DHCP / Static IP mode
- Supports TCP/IP, ICMP, ARP, DHCP client, DNS, FTP client, POP3, SMTP, Telnet server and UDP protocols
- 10/100Mbps Ethernet
- Web-based configuration
- LED I/O to reflect Ethernet connection and link activity
Serial Port Features:
- High speed (921.6Kbps) UART
- Baud rates:2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600
- Parity Bits: Odd, Even, None
- Data Bits: 7, 8 ~ Stop Bits: 1 or 2
- Hardware (RTS/CTS) flow control
- Remotely access serial port via Internet application
- 640/576 bytes Transmit/Receive FIFO buffer.
HM4 Modem Features (LSDB-8301HM or LSDB-8301HC):
- Maximum Data Rate: 56,000 bps ~ V.92
- Send/ Receive 14.4K Fax class 1 and 1.0
- Extension Pickup and Line in use Detection
- Automatic Auto Answer Feature
- SIA alarm
- TAM (Telephone Answering Machine Voice Playback and Remote Recording)
- Type I Caller ID (On Hook Caller ID) and Type II Caller ID (Call Waiting Caller ID)
- ITU V Standards Supported: V.92, V.90, V. 80, V.44, V.42, V.42bis, V.34, V.32bis, V.32, V.29 Fast POS, V.27 ter, V.253, V.251, V.250, V.22 bis, V.22, V.22 bis Fast Connect, V.23, V.21, V.17 as well as Bell 212A, and Bell 103 Standards
Tiny Modem Features (LSDB-8302T):
- Maximum Data Rate: 56,000 bps ~ V.92
- Send/ Receive 14.4K Fax class 1 and 1.0
- Extension Pickup and Line in use Detection
- Automatic Auto Answer Feature
- TAM (Telephone Answering Machine Voice Playback and Remote Recording)
- Type I Caller ID (On Hook Caller ID) and Type II Caller ID (Call Waiting Caller ID)
- ITU V Standards Supported: V.92, V.90, V. 80, V.44, V.42, V.42bis, V.34, V.32bis, V.32, V.29 Fast POS, V.27 ter, V.253, V.251, V.250, V.22 bis, V.22, V.22 bis Fast Connect, V.23, V.21, V.17 as well as Bell 212A, and Bell 103 Standards
Rating:
Parameter
|
Min
|
Typical
|
Max
|
Units
|
Operating Temperature*
|
|
25
|
|
°C
|
Relative Humidity
(non-condensing)
|
5
|
-
|
95
|
%
|
Voltage Requirement
|
4.75
|
5
|
5.25
|
VDC
|
Power Consumption
|
|
|
|
mW
|
Power Consumption-TX mode |
|
206 |
|
mA |
Power Consumption-RX mode |
|
173 |
|
mA |
* Note: Performance may
degrade some when operating temperature range is
over -30°C or +80°C |
|
LSDB-8300M Size:
|
2.30″ x 1.21″ x 0.54″ (58.3 x 30.6 x 13.8mm)
- included pin headers height 0.23” (5.8mm)
|
LSDB-8300NE Size:
|
2.89″ x 1.24″ x 0.56″ (73.3 x 31.4 x 14.3mm)
|
LSDB-8302T Size:
|
2.36″ x 1.62″ x 0.81″ (60.0 x 41.0 x 20.6mm)
|
LSDB-8303A Size:
|
4.33″ x 3.55″ x 0.88″ (110.0 x 90.0 x 22.3mm)SDB-8303A
|
LSDB-8301HM Size:
|
2.74″ x 1.38″ x 0.63″ (69.5 x 35.0 x 16.1mm)
|
Ordering Information:
Model Number
|
Description
|
LSDB8300M
|
LAN-to-Serial DIP Module with through Hole (DIP) pins for the RS232 interface, and Ethernet pins that allow the Jacks to be placed in preferred locations.
Model:
LSDB8300M
|
LSDB8300NE
|
LAN-to-Serial Adapter Board with on board DB9 connector and RJ45 jack that allow the flexibility of Serial port cable length.
Model:
LSDB8300NE
|
LSDB8300MB
|
The Base Board for LSDB8300M DIP module. This development board provides DB-9, USB, RJ-45 interface connectors for easy implementation and testing purpose.
Models:
LSDB8300MB
|
LSDB8300EVK
|
Each LSDB8300EVK evaluation kit contains the following items:
1ea ~ LSDB8300M
1ea ~ LSDB8300MB
1ea ~ RJ-45 Ethernet Cable
1ea ~ USB (A to B) cable
1ea ~ DB9 Null Modem Cable
|
LSDB-8302T
|
LAN-to-Modem adaptor Board with RJ-11 built-in Tiny modem and on board RJ45 jack that allows Anlog phone line to Ethernet communication capability.
Model:
LSDB-8302T
|
LSDB-8303A
|
LAN to Serial and Modem standalone device with one RS232 and 3 out of 4 options:
1) RS232/RS485
2) USB host
3) HM4
4) WiFiHU2
Model:
LSDB-8303A
|
LSDB-8301HM
| | | | |